HOW TO SET UP A TUB YOURSELF

How to Set up a Tub Yourself

How to Set up a Tub Yourself

Blog Article

Information

Just how do you really feel on the subject of Tools You Need to Install a New Bathtub ?


A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't specifically rocket science, however it does need solid plumbing, woodworking, and also occasionally, tiling skills. Changing an old bath tub with a brand-new one is additionally a reasonably hard project. If the old tub is easily easily accessible, the job can move immediately; if you need to open up a wall surface to get rid of the old bathtub and also position the new tub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. Ensure you have actually certified on your own for the work and also fit trying it. Rather than hiring a contractor to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you might require a specialist plumber to make tube links.
This write-up will certainly aid you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to transform the setup of your previous water pipelines.
Your devices and also product list must make up the following:
  • New Tub
  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Getting ready for the Setup


    Firstly, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's instructions. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
    Fit the versatile tap ports to the bottom of the two faucets making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the supplied washing machines.
    Link the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final position.

    Removing Old Touches


    If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing taps can be rather problematic because of the restricted access that is usually the situation.
    Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
    Prior to proceeding to fit the brand-new taps, contrast the pipe connections on the old faucets to the new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Installing the Bath tub


    Using both wood boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of focusing all the weight onto four little factors.
    The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bath tub until the spirit level checks out degree.
    To install taps, fit all-time low of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; then do the exact same for the various other tap.
    Turn on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if necessary. Fill up the bath tub as well as also check the overflow outlet as well as the regular electrical outlet for leaks.
    Finally, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub needs to wait until the bathtub has been utilized a minimum of when as this will certainly resolve it right into its last position.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damage to the thread. One end of the port fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipe.
    Next, position the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in area in between the faucet as well as the sink. Protect the faucet in place with the producer offered backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal tap connectors. The previous kind must be linked to the tap ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Tiling Around the Bathtub


    In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to break a rigid seal, causing the water to pass through the wall surface between the bath and also the tiling, causing problems with dampness and also possible leaks to the ceiling listed below.
    You can pick from a range of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also can sealing voids approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealant can split fairly very early if you do not take into consideration this movement prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I hope you liked our piece on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thank you so much for finding the time to browse our article post. Are you aware of another individual who is excited by Installing A Bathtub? Why not share it. We love reading our article about How to Install a Bathtub.




    Order Repair


    Report this page